Best Barns denver_1220df Manuale delle Istruzioni

Manufactured by Reynolds Building Systems, Inc.205 Arlington Drive Greenville, PA 16125 724-646-3775This manual is copyrighted. Under the copyright

80-1/4” Wall Studs68-1/2" Wall PlateStep 7 Assemble Back Wall1. Position (4) four 2x4x68-1/2" boards together and indicate with 'X&apos

Step 8 Build Center Wall Brace & Set Walls5. Set the back wall panel between the sidewalls. Secure the wall panels together at the corners.Use (4)

Step 8 ContinuedInstall the center Wall Brace in the center of the building between the sidewalls.Make sure the sidewalls are straight. The shorter 2x

1. Install a 6' long 2x4 board as a tie plate over the sidewall plate. Use 10d sinkers.2. Install a 7' long 2x4 and cut another 7' lon

Step 12 Install Gable Support Shelf4. Cut a (2) two 2x4s to a length of 10-1/4".5. Nail the 2x4 blocks to the rear corners, flush with the top of

Step 13 Layout Roof TrussesRear Gable24"23-1/4"Gable TrimStarting at the back of the building, layout the truss spacing. Measure from the fa

Metal Truss HangerSoffit Board Flush With Siding1. Place trusses over the 'X' marks. Install 2x4 hangers to the 2x4 plate using (4) four 1-1

Insert (2) two plyclips into the roof sheathingbetween each truss at the top row.3. Apply roof sheathing across the top of the roof. There will be an

1. Install loft door trim panel on the front gable by screwing through the back of the sidingwith 1" galv. screws.Building Tip: Install ridge ve

Step 18 Install DoorsBefore you fasten the hinges to the doortrim, temporarily prop the doors in theopening. Tip; set the door stop on a pieceof sidin

When measurements are given for a boardlength or width, it is from the longest side.measure from hereTool ListHammer & Hand SawFraming Square &

Shingles by Owner 14 Bundles Shingles 9 pcs. Roof 'drip' EdgeDenver-R 12'x 20' Barn kit Packing ListQty. Qty.4 Wall Tie Plates 84

1. Stagger the 4x4 timbers as shown below. Cut (2) two 2x4-8' boards into 2' long blocksto secure the 4x4s where they butt together.Assembly

2. Repeat to assemble another Gable Plate Assembly72" long 2x43/4" Plywood Gusset2x4 BlockGable Plate AssemblyStep 1 Assemble Trusses6. Nail

6. Repeat steps to assemble the front roof gable.Step 2 Assemble Roof Gables1. Place (2) two 61" long and 34-3/4" long 2x4 gable rafters in

XXXXButt (2) two 68-1/2" boards together. Center a 2x4-6' board (used as door spacer) on top and screwthe boards together using (4) four 2-1

2x4-6' Door SpacerStep 5 Assemble Front Wall (doors centered)2x6 Door HeaderSiding 3/4"Below HeaderCut EdgeTongue EdgeCut EdgeButt Square Ed

Cut the siding flush with thebottom plate if installing thebuilding on a cement slab.Step 6A Assemble 10' Long Sidewalls4. Square wall frame. Mea

4. Repeat to apply siding to the other 10' wall frame.Step 6B Assemble Sidewalls for 20' Building Length1. Select one of the 10' sidewa